the truss system is not heavy at all and does not leave any dimples in the 2 inch foam top at all. We have 120lb girls who can grab and move them without help. we have left the cover and trusses in place for as long as a week without it leaving a single mark in the top pad
moving them away from the pit is simple as we move the top cover and the truss system completely out of the way and place them behind our bleachers ( in the background of the pic) daily.
We put our standards in a storage building each night as well. with no help at all, I can put up the standards, place the trusses and cover the pit in 15 minutes
in any case, the truss concept arches the entire top pad and does not allow any pooling on the pad at all. Good luck with your project
Lifting weather cover to prevent pool
Moderator: Barto
- KirkB
- PV Rock Star
- Posts: 3550
- Joined: Mon May 19, 2008 6:05 pm
- Expertise: Former College Vaulter; Former Elite Vaulter; Former Coach; Fan
- Lifetime Best: 5.34
- Favorite Vaulter: Thiago da Silva
- Location: Vancouver, BC, Canada
Re: Lifting weather cover to prevent pool
This topic was raised last year, but I just noticed this Pit Drainage Insert product today:
http://www.everythingtrackandfield.com/webapp/wcs/stores/servlet/Product2_10152_10753_2004429_-1_2000205_2000204_2000192_ProductDisplayErrorView
For someone looking to buy instead of build, this looks like it would do the job!
It also might give some DIYers some ideas on how to build one yourself. From the pic, you can see that it doesn't need to be very big or very complicated. It's just a couple of pipes bent at right angles and fastened together! Just be sure that there's no sharp cuts on the pipe that might slice into your top pad.
If I was building this, I'd use 1/2" PVC pipe (cut a 10' length into 4 x 30" legs), with 2 x 90 degree PVC pipe corners. Then I'd add one or two more 90 degree corners to set the right angle between the 4 pipes, and then duct tape it all together. Instead of the usual grey duct tape, a high-temperature metal foil tape (the type used to seal over-the-range microwave oven vents) might last longer. You can buy all these supplies at Home Depot or Lowe's.
Kirk
http://www.everythingtrackandfield.com/webapp/wcs/stores/servlet/Product2_10152_10753_2004429_-1_2000205_2000204_2000192_ProductDisplayErrorView
For someone looking to buy instead of build, this looks like it would do the job!
It also might give some DIYers some ideas on how to build one yourself. From the pic, you can see that it doesn't need to be very big or very complicated. It's just a couple of pipes bent at right angles and fastened together! Just be sure that there's no sharp cuts on the pipe that might slice into your top pad.
If I was building this, I'd use 1/2" PVC pipe (cut a 10' length into 4 x 30" legs), with 2 x 90 degree PVC pipe corners. Then I'd add one or two more 90 degree corners to set the right angle between the 4 pipes, and then duct tape it all together. Instead of the usual grey duct tape, a high-temperature metal foil tape (the type used to seal over-the-range microwave oven vents) might last longer. You can buy all these supplies at Home Depot or Lowe's.
Kirk
Run. Plant. Jump. Stretch. Whip. Extend. Fly. Clear. There is no tuck! THERE IS NO DELAY!
- KirkB
- PV Rock Star
- Posts: 3550
- Joined: Mon May 19, 2008 6:05 pm
- Expertise: Former College Vaulter; Former Elite Vaulter; Former Coach; Fan
- Lifetime Best: 5.34
- Favorite Vaulter: Thiago da Silva
- Location: Vancouver, BC, Canada
Re: Lifting weather cover to prevent pool
vaultmd wrote:Beach balls work
Actually, I like vaultmd's idea even better!

What could be simpler?
But at least I've answered CowtownPV's original question about a commercial off-the-shelf product.
Kirk
Run. Plant. Jump. Stretch. Whip. Extend. Fly. Clear. There is no tuck! THERE IS NO DELAY!
Return to “Pole Vault - Equipment”
Who is online
Users browsing this forum: No registered users and 19 guests